The fastest way to write a good punch list is to start from specific, well-worded items and edit the brackets, not to invent each line from a blank page. Most defects found at closeout repeat from job to job: paint scuffs, doors that rub, caulk gaps, missing cover plates. A reference list gives you the wording, so every item says where the problem is, what is wrong, and what the fix is.
This guide is a reference you can copy into your punch list tool or spreadsheet. Items are grouped by trade, written to be actionable in one visit, and marked with placeholders in [brackets]. Use it alongside the construction punch list template and closeout checklist, which gives you the header, columns, and sign-off structure.
How to Word a Punch List Item
Every item should answer three questions: where, what, and what to do.
Formula: [Location] + [Defect, with size or count] + [Required action or standard]
|
Weak
|
Strong
|
|
Paint
|
[Room], [wall] has 3 scuffs, 4 to 5 ft above floor. Touch up with [color, sheen].
|
|
Door sticks
|
[Room] [door] rubs at latch side top. Adjust hinges or plane edge.
|
|
Caulk
|
Gap at [location], about [length]. Remove old caulk, clean, recaulk in [color].
|
|
Outlet
|
[Room] outlet at [location] has no power. Test circuit, repair, and verify.
|
Add a photo with a marker or arrow showing the problem. For each item, also record trade, assigned person, due date, and verified by. A clear item means the sub fixes it in one visit and sends one photo. For the process of running the walkthrough and tracking items to closed, see the construction project closeout guide.
Site and Exterior
- [ ] Grading near [location] slopes toward the building. Regrade to slope away
- [ ] Standing water at [location] after rain. Correct drainage
- [ ] Downspout at [location] discharges next to foundation. Add extension or splash block
- [ ] Concrete flatwork at [location] has a crack, [length]. Evaluate and repair per spec
- [ ] Concrete surface at [location] has scaling, staining, or an uneven finish. Repair or clean
- [ ] Control joints at [location] not cut or not sealed. Complete
- [ ] Driveway or walkway edge at [location] is damaged. Repair
- [ ] Exterior light at [location] is not operating. Repair or replace
- [ ] Gate at [location] does not latch. Adjust
- [ ] Fence post at [location] is loose or out of plumb. Reset
- [ ] Construction debris, nails, and scrap remain at [area]. Remove and sweep
- [ ] Landscaping at [location] is damaged during construction. Restore
- [ ] Irrigation head at [location] is damaged or misaligned. Repair and test the zone
- [ ] Sod or seeding at [area] has bare patches. Repair
- [ ] House numbers and mailbox installed per [requirement]
Concrete and Masonry
- [ ] Concrete at [location] has honeycombing or voids. Patch per spec
- [ ] Form marks, fins, or lips at [location]. Grind smooth
- [ ] Slab at [location] has a crack wider than [spec]. Evaluate and repair
- [ ] Exposed rebar or tie wire at [location]. Cut back and patch
- [ ] Anchor bolt at [location] is out of tolerance. Correct
- [ ] Brick or block at [location] has chips or cracks. Repair or replace the unit
- [ ] Mortar joints at [location] are incomplete or inconsistent. Tuck point
- [ ] Efflorescence at [location]. Clean per manufacturer instructions
- [ ] Weep holes at [location] are blocked or missing. Open or install
- [ ] Control joints in masonry at [location] not caulked. Complete
- [ ] Stone veneer at [location] has loose pieces or gaps. Reset and grout
- [ ] Concrete stains, drips, and spatter on adjacent surfaces. Clean
Framing and Carpentry
- [ ] Wall at [location] is out of plumb or bowed beyond tolerance. Correct
- [ ] Floor at [location] squeaks. Fasten subfloor to joists
- [ ] Floor at [location] is uneven by more than [tolerance]. Correct
- [ ] Door opening at [location] is out of square. Correct
- [ ] Trim joint at [location] has a gap greater than [size]. Refit or fill
- [ ] Casing at [location] has nail holes unfilled. Fill and sand
- [ ] Baseboard at [location] has visible gaps at corners. Recut or fill
- [ ] Crown molding at [location] has open miters. Adjust
- [ ] Stair tread at [location] squeaks or is loose. Fasten
- [ ] Handrail at [location] is loose or at the wrong height. Secure or adjust per code
- [ ] Baluster at [location] is loose. Secure
- [ ] Blocking missing at [location] for [fixture or cabinet]. Add and mark
- [ ] Exposed fasteners or splits in trim at [location]. Repair
- [ ] Attic access at [location] does not close or seal. Adjust
- [ ] Deck board at [location] is split, raised, or has protruding fasteners. Replace or set
- [ ] Deck railing at [location] is loose. Secure to meet load requirements
Roofing and Exterior Envelope
- [ ] Shingles at [location] are damaged, missing, or misaligned. Repair
- [ ] Exposed nail heads at [location]. Seal or replace
- [ ] Flashing at [location] is not sealed or is improperly lapped. Correct
- [ ] Pipe boot at [location] is cracked or unsealed. Replace
- [ ] Ridge cap at [location] has gaps or lifted pieces. Fasten and seal
- [ ] Gutter at [location] has a gap, sag, or leak at the seam. Repair
- [ ] Downspout at [location] is disconnected or damaged. Reconnect
- [ ] Roof debris and nails remain in [area]. Clean, with a magnetic sweep
- [ ] Siding at [location] has gaps, scratches, or loose pieces. Repair
- [ ] Siding at [location] is missing sealant at penetrations. Seal
- [ ] Trim at [location] has open joints. Caulk and paint
- [ ] House wrap at [location] is torn or unsealed. Repair before cover
- [ ] Soffit or fascia at [location] is damaged or loose. Repair
- [ ] Exterior paint at [location] has missed areas or runs. Touch up
For roofing workflows and documentation, see the roofing project manager role guide.
Windows and Doors
- [ ] Window at [location] does not open, close, or lock smoothly. Adjust
- [ ] Window glass at [location] has a scratch, chip, or crack. Replace or polish
- [ ] Window screen at [location] is missing or damaged. Install or repair
- [ ] Window flashing or sealant at [location] is incomplete. Complete
- [ ] Weatherstripping at [door or window] has gaps. Adjust or replace
- [ ] Door at [location] rubs, sticks, or does not latch. Adjust hinges, strike, or edge
- [ ] Door gap at [location] is uneven, more than [tolerance]. Adjust
- [ ] Door lock at [location] does not operate or is keyed incorrectly. Repair or rekey
- [ ] Door closer at [location] is too fast, slow, or does not latch. Adjust
- [ ] Door stop at [location] is missing. Install
- [ ] Threshold at [location] is loose or has gaps. Secure and seal
- [ ] Sliding door at [location] binds. Adjust rollers and track
- [ ] Garage door at [location] does not close evenly or the opener is not set. Adjust
- [ ] Exterior door finish at [location] is scratched or unfinished. Touch up
- [ ] Hardware at [location] is loose or mismatched. Tighten or replace
Insulation and Air Sealing
- [ ] Insulation at [location] is missing, compressed, or has gaps. Install per spec
- [ ] Attic insulation depth at [location] is below spec. Add
- [ ] Baffles at [location] are missing at eave vents. Install
- [ ] Air sealing at [penetration] is incomplete. Seal
- [ ] Vapor barrier at [location] is torn. Repair and tape
- [ ] Spray foam at [location] has overspray on finished surfaces. Remove
- [ ] Attic hatch at [location] is not insulated or weatherstripped. Complete
Photograph insulation before the walls close. After drywall, you cannot verify it.
Drywall
- [ ] Wall at [location] has visible joint or tape seams. Re-skim, sand, and repaint
- [ ] Nail or screw pops at [location]. Reset, patch, and paint
- [ ] Wall at [location] has dents, gouges, or holes. Patch
- [ ] Corner bead at [location] is damaged or not straight. Repair
- [ ] Ceiling at [location] has visible seams, cracks, or roller marks. Repair
- [ ] Texture at [location] does not match adjacent areas. Match
- [ ] Drywall at [location] has sanding dust or residue on surfaces. Clean
- [ ] Penetration at [location] has gaps around the box or pipe. Patch
- [ ] Fire-rated assembly at [location] has gaps or missing fire caulk. Complete per detail
- [ ] Access panel at [location] is not installed or does not close. Install or adjust
Check drywall in raking light, using a bright flashlight held at a low angle to the wall. Defects that disappear in normal light show up clearly.
Painting and Finishes
- [ ] Wall at [location] has scuffs or marks, [count]. Touch up with [color, sheen]
- [ ] Paint coverage at [location] is uneven or shows through. Recoat
- [ ] Cut line at [ceiling, trim, or corner] is not clean. Correct
- [ ] Paint drips or runs at [location]. Sand and repaint
- [ ] Paint on [window, hardware, or fixture] needs removal. Clean
- [ ] Trim at [location] has missed spots or brush marks. Repaint
- [ ] Caulk at [location] has gaps before painting. Caulk and repaint
- [ ] Color at [location] does not match the approved selection. Verify and correct
- [ ] Ceiling at [location] has roller marks or flashing. Recoat
- [ ] Doors at [location] have unpainted edges or tops. Paint
- [ ] Touch-up paint left for the owner, labeled by room and color
- [ ] Stain or clear coat at [location] is uneven. Correct
- [ ] Wallcovering at [location] has a bubble, seam gap, or tear. Repair
Flooring
Tile
- [ ] Tile at [location] is cracked, chipped, or loose. Replace
- [ ] Tile surface at [location] is lippage-prone or uneven beyond tolerance. Correct
- [ ] Grout at [location] has gaps, pinholes, or color variation. Regrout
- [ ] Caulk at tile corners and changes of plane at [location] is missing. Install
- [ ] Tile at [location] sounds hollow. Evaluate and repair
- [ ] Grout haze remains on [location]. Clean
Hardwood and engineered
- [ ] Boards at [location] have gaps, cupping, or squeaks. Correct
- [ ] Finish at [location] has scratches, bubbles, or uneven sheen. Repair
- [ ] Transitions at [location] are loose or missing. Install
Vinyl, LVP, and laminate
- [ ] Planks at [location] have gaps or lifted edges. Correct
- [ ] Seams at [location] are visible or open. Repair
- [ ] Damaged planks at [location]. Replace
Carpet
- [ ] Seams at [location] are visible or open. Repair
- [ ] Carpet at [location] has wrinkles or loose areas. Restretch
- [ ] Stains or marks at [location]. Clean or replace
General
- [ ] Transition strips at [location] are missing or loose. Install
- [ ] Baseboard or shoe at [location] has gaps from the floor. Fill or fit
- [ ] Floor protection removed and floor cleaned in [area]
Cabinets, Millwork, and Countertops
- [ ] Cabinet door at [location] is misaligned. Adjust hinges
- [ ] Drawer at [location] binds or does not close fully. Adjust
- [ ] Soft-close mechanism at [location] does not work. Adjust or replace
- [ ] Cabinet hardware at [location] is loose or inconsistent. Tighten and align
- [ ] Cabinet face frames at [location] have gaps to the wall. Scribe and caulk
- [ ] Finish at [location] has scratches, chips, or touch-up needed. Repair
- [ ] Shelves at [location] are missing or loose. Install
- [ ] Countertop at [location] has a chip, scratch, or stain. Repair or replace
- [ ] Countertop seam at [location] is wide or visible. Correct
- [ ] Backsplash caulk at [location] is missing or uneven. Install
- [ ] Sink cutout edges at [location] are rough or unsealed. Finish and seal
- [ ] Fillers and end panels at [location] are not installed. Install
- [ ] Closet rods, shelves, and brackets at [location] installed per plans
Plumbing
- [ ] Faucet at [location] leaks, drips, or has weak flow. Repair
- [ ] Drain at [location] is slow or gurgles. Clear and test
- [ ] Leak under sink at [location]. Repair and dry
- [ ] Toilet at [location] rocks, runs, or does not flush properly. Correct
- [ ] Shower valve at [location] has incorrect hot and cold orientation. Correct
- [ ] Shower pan or tub at [location] has scratches or damage. Repair
- [ ] Hot water at [location] is slow to arrive or not hot. Evaluate
- [ ] Shutoff valves at [location] are not labeled or do not operate. Label and test
- [ ] Escutcheon at [location] is loose or unpainted. Secure
- [ ] Caulk at [fixture] is missing. Install
- [ ] Aerators, strainers, and handles at [location] are installed. Complete
- [ ] Hose bibs at [location] leak or are not insulated or protected. Correct
- [ ] Water heater at [location] is not labeled, drained, or set to the right temperature. Set per spec
- [ ] Plumbing tests and required inspections documented
Electrical and Low Voltage
- [ ] Outlet at [location] has no power. Test and repair
- [ ] Outlet at [location] is loose, crooked, or has a missing cover plate. Secure
- [ ] GFCI at [location] does not trip or reset. Replace and test
- [ ] Switch at [location] controls the wrong fixture or does not work. Correct
- [ ] Light fixture at [location] flickers, buzzes, or is not secure. Repair
- [ ] Bulbs missing or wrong color temperature at [location]. Install or replace
- [ ] Dimmer at [location] hums or does not match the fixture. Replace
- [ ] Panel at [location] is not labeled or has an incorrect schedule. Label
- [ ] Smoke or CO alarm at [location] is not installed or tested. Install and test
- [ ] Exhaust fan at [location] is loud, does not run, or is not vented. Correct
- [ ] Doorbell, thermostat, or controls at [location] not working. Repair
- [ ] Data and cable outlets at [location] are not terminated or labeled. Complete
- [ ] Wiring or boxes exposed at [location]. Cover and secure
- [ ] Exterior outlets at [location] lack weatherproof covers. Install
HVAC and Mechanical
- [ ] Room at [location] is too hot or cold. Balance airflow
- [ ] Register or grille at [location] is loose, damaged, or missing. Secure or replace
- [ ] Return air at [location] is blocked or undersized. Evaluate
- [ ] Thermostat at [location] is not calibrated or labeled. Program and label
- [ ] Equipment at [location] has unusual noise or vibration. Evaluate
- [ ] Condensate line at [location] does not drain. Correct
- [ ] Filters not installed or the wrong size. Install
- [ ] Ductwork at [location] is unsealed or unsupported. Seal and support
- [ ] Flue or vent at [location] is not sealed or has improper clearance. Correct
- [ ] Equipment startup and balancing report not delivered. Provide
- [ ] Disconnects and service access at [location] are blocked or unlabeled. Clear and label
Fire, Life Safety, and Accessibility (Commercial and Multifamily)
- [ ] Exit sign at [location] is not illuminated or is the wrong orientation. Correct
- [ ] Emergency lighting at [location] fails the test. Repair
- [ ] Fire alarm device at [location] is not installed or tested. Complete
- [ ] Sprinkler head at [location] has paint, obstruction, or incorrect clearance. Correct
- [ ] Fire extinguisher at [location] is missing, or lacks a tag or signage. Install
- [ ] Fire caulk at [penetration] is incomplete. Complete per detail
- [ ] Rated door at [location] has a missing label, gap, or closer. Correct
- [ ] Door hardware at [location] is not at the required height or clearance. Adjust
- [ ] Required signs at [location] are missing or incorrect. Install
- [ ] Required inspections are not signed off. Schedule and complete
Requirements vary by jurisdiction and occupancy. Verify against the plans and local code. For commercial interiors, see the commercial tenant improvement punch list template covering priority levels and occupancy gates.
Appliances and Specialties
- [ ] Appliance at [location] is not level, connected, or running. Correct
- [ ] Appliance at [location] has dents or scratches. Repair or replace
- [ ] Appliance manuals, warranty cards, and registration delivered
- [ ] Range hood at [location] is loud or not ducted. Correct
- [ ] Garbage disposal at [location] does not run or leaks. Repair
- [ ] Mirror at [location] is crooked, scratched, or unsecured. Correct
- [ ] Shower door at [location] leaks, binds, or has a gap. Adjust and seal
- [ ] Towel bars, paper holders, and hooks at [location] are loose or at the wrong height. Reset
- [ ] Blinds or shades at [location] are not installed or are damaged. Install
- [ ] Fireplace at [location] is not tested or lacks a manual. Test and deliver
- [ ] Garage door remotes, keypad, and codes delivered
Cleaning and Closeout Deliverables
- [ ] Windows and glass at [location] have stickers, paint, or smudges. Clean
- [ ] Floors at [location] have dust, residue, or construction debris. Clean
- [ ] Fixtures and surfaces at [location] have adhesive, label residue, or dust. Clean
- [ ] Cabinet interiors and drawers at [location] have debris. Clean
- [ ] Protective film and tape remain at [location]. Remove
- [ ] HVAC vents and registers contain dust. Clean
- [ ] Trash, pallets, and temporary facilities removed
- [ ] Keys, remotes, and access cards delivered
- [ ] Manuals, warranties, and as-built drawings delivered
- [ ] Spare tile, paint, and attic stock delivered and labeled
- [ ] Owner walkthrough and training completed
Using the Reference Well
Do not paste all of it. Use these lists as a prompt during your own pre-walk, and as wording examples. Paste only what you actually find.
Tips
- Walk in a consistent order: exterior, then room by room, then systems
- Photograph each item, with a marker for scale
- Assign one trade per item, with a due date
- Batch fixes by trade and area, so each sub makes one visit
- Verify each completed item and take a second photo
- Close the item only when the person who raised it accepts
Track the hours spent on pre-walk and corrections under a closeout cost code. GPS time tracking captures crew time by project, so you can see what closeout costs and compare it across jobs. For crew setup, see time tracking for construction workers and construction time tracking software.
After several projects, count which items repeat. If paint touch-ups, caulk, and door adjustments dominate your lists, change the process upstream: protect finished surfaces, add a quality check before the next trade, and train the crews responsible. See the field inspection workflow for inspection checklists that catch problems before they become punch items.
Contract and Payment Notes
Define how punch lists work before the job ends.
- Who creates and signs off the list
- When the list is final, and how later items are handled
- How long you have to complete items
- How much is held back for open items, and when it is released
- What happens to disputed items
See how to negotiate a construction contract for completion and payment language, and construction retainage for how holdbacks are released. Open items delay cash. See construction cash flow management. When a sub fails to fix items on time, document each missed date. See how to fire a subcontractor. For the record that protects you after closeout, see construction defect claims.
Use the data to improve estimates. See how to win construction bids and contractor profit and loss statement. For platform comparison on time tracking tools, see top 5 time tracking apps, top 5 BusyBusy alternatives, and TaskTag vs. BusyBusy. For exterior and site crews, see time tracking for landscapers.
Related Resources
Punch List and Inspection:
TaskTag Features:
Related Blog Posts: